Fire-resistant cable ducts: reliable protection for electrical and mechanical installations
Electrical cables without adequate fire protection fail in a fire and lose circuit integrity – which is essential for the safety of people and for firefighting. Many cables must keep working during evacuation to power emergency lighting, signalling and smoke extraction systems.
Fire-resistant cable ducts – Aestuver® Standard and Aestuver® Exclusive cable ducts – protect critical systems in residential buildings, industrial complexes and underground infrastructure such as metro stations and road and rail tunnels. Their main components are Aestuver® fire protection boards and fixing elements. The boards form cable ducts that are fire-resistant on two, three or four sides, installed either freestanding or wall-mounted.
These fire-resistant enclosures for electrical cables are covered by European Technical Assessment ETA-21/0755 (issued 24 September 2021) and combine high-quality fire protection boards, robust construction and proven performance.
What are Aestuver® fire-resistant cable enclosures?
Standard cable ducts
The Aestuver® range comprises two main types of fire-resistant cable enclosures. The first type, Standard cable ducts, is assembled by local specialists from standard or bespoke Aestuver® fire protection boards. All components are supplied as individual parts for assembly and installation on site.
Exclusive cable ducts
The second type, Exclusive cable ducts, are prefabricated, factory-made insulated enclosures that provide thermal and mechanical protection. They protect cables for life safety, fire suppression and other critical systems routed through the enclosure, maintaining circuit integrity even in a fire outside the enclosure.
Exclusive cable ducts are divided into E-ducts and I-ducts.
Exclusive cable ducts (E-ducts)
Exclusive fire-resistant cable ducts (E-ducts)
The prefabricated Aestuver® cable duct system maintains the functional integrity of electrical installations: in a fire, no heat from outside enters the duct and the temperature inside stays low, so there is no short circuit or power interruption. These cable ducts are tested to DIN 4102-12.
Exclusive cable ducts (I-ducts)
Exclusive fire-resistant cable ducts (I-ducts)
Aestuver® I-ducts prevent fire spreading from inside the duct to the outside and protect adjacent areas such as escape and rescue routes (fire load protection). These cable ducts are tested to DIN 4102-11.
Fire-resistant cable ducts: how they are made
Aestuver® fire-resistant cable ducts are made from Aestuver® fire protection boards – cement-bonded, glass-fibre-reinforced lightweight concrete, a non-combustible Euroclass A1 material to EN 13501-1. Both the base board and the finished cable enclosures hold their own European Technical Assessment, so the prefabricated elements meet the requirements as well as their components. As a result, the fire-resistant cable enclosures resist combustion and minimise the spread of fire and smoke.
Design of fire-resistant cable ducts: two main components
Prefabricated cable duct (base section):
Forms the base and side walls and provides a stable foundation for holding the cables.
Made from single-layer Aestuver® boards for PLCD cable ducts or thicker boards for PLCS cable ducts, in thicknesses from 30 mm (EI 60) to 50 mm (EI 90).
Cable duct cover:
A protective cover that seals the duct and is available in a single-layer (PLCS) or double-layer (PLCD) version, depending on fire safety requirements.
Fixed with Aestuver™ fire protection adhesive and steel fasteners (clips or screws) for a tight, fire-resistant seal.
For PLCS fire protection ducts, the covers are laid loosely over the ducts and reinforced along the long edges with 40 mm wide blanking strips, which are glued and stapled at intervals of approximately 100 mm. A 100 mm wide cover strip seals the butt joints and is secured with staples to keep the installation intact, even in complex areas such as corners.
For PLCD fire protection ducts, the duct and cover are bonded with adhesive and secured with screws (spaced 280–330 mm apart) or clips (spaced 100–120 mm apart), while steel spacers (e.g. OBO BSKB1026) anchor the duct to walls, ceilings or floors with a minimum thickness of 100 mm and a density of ≥350 kg/m³.
Penetrations and joints are carefully sealed:
Columns: Filled with rock wool (120–140 kg/m³, melting point > 1000 °C), and covered with Aestuver® panel collars (15–40 mm thick, depending on the fire resistance class), which are glued and stapled in place to ensure a flush surface.
Foam strips: 5 mm thick, single-sided adhesive foam strips, class B1, seal the butt joints between adjacent ducts, thereby improving airtightness.
Thanks to this modular design, fire-resistant cable ducts can be adapted to a wide range of project requirements while maintaining their structural and fire-resistant integrity.
Proven fire resistance
Aestuver® fire-resistant cable ducts undergo rigorous testing (test methods: DIN EN 1366-5:2010-06, DIN EN 1363-1:2012-10) and are classified to EN 13501-2:2016:
PLCD: EI 30, EI 45, EI 60, EI 90 (integrity and insulation) and E 120 (integrity only).
PLCS: EI 60, EI 90 and E 120.
The EI classification covers integrity (E) and thermal insulation (I) for up to 90 minutes, keeping the side not exposed to fire below critical temperatures; the E classification covers integrity for up to 120 minutes.
This makes Aestuver® fire-resistant enclosures for electrical cables ideal for keeping life-safety systems such as emergency lighting and ventilation running during a fire.
What is the maximum cable load for fire-resistant enclosures?
The fire-resistant cable enclosures are designed to withstand substantial cable loads, tailored to their size and configuration:
PLCD models (EI 30 to EI 90): Can support up to 15.34 kg/m, with dimensions ranging from 290 mm wide × 145 mm high (EI 30) to 340 mm wide × 165 mm high (EI 90).
PLCS models (EI 60 and EI 90): Designed for loads of up to 31.84 kg/m, with larger dimensions of 1,250 mm wide by 1,000 mm high.
What is the maximum usable cross-section of Aestuver® prefabricated fire-resistant cable ducts?
All models offer a usable cross-section ranging from 260 × 105 mm to 1,150 × 900 mm, thereby ensuring consistent cable capacity.
With PLCS ducts, cables can rest directly on the floor or on additional supports, with the load-bearing capacity of the support determining the maximum load, which offers flexibility for heavier installations.
Which suspension system is used for fire-resistant cable ducts?
The suspension system must be made of steel and designed to withstand the loads encountered in the relevant project, with the maximum permissible distance between suspension brackets being 1250 mm.
What are the maximum dimensions for cables in the fire-resistant cable ducts?
Aestuver® fire-resistant cable ducts allow precise cable routing:
Single cable: Maximum diameter of 21 mm, reinforced with 80 × 80 mm Aestuver® plate supports.
Cable bundle: Maximum diameter of 45 mm, reinforced with 100 × 100 mm plate supports.
Sealing: The penetrations shall be sealed using materials that comply with the requirements of ETA 15/0556 (or equivalent standards), with the drill holes complying with the specifications set out in Annexes A3 and A11 (e.g. D1 ≥ 20 mm, dry coating thickness D2 ≥ 1.0 mm).
These limits ensure that fire and smoke cannot penetrate the fire-resistant cable ducts, thereby maintaining their protective barrier.
Versatile, durable fire protection for cable routes
Aestuver® fire-resistant service ducts are classified as Type X for all indoor and outdoor applications and have a proven track record in demanding environments such as tunnels, industrial facilities and high-rise buildings.
The PLCS version, with a maximum span of 1,250 mm between supports (e.g. C-rails or brackets), is suitable for suspended installation, while the directly mounted PLCD version is particularly well suited to confined spaces.
With a service life of at least 25 years and a tensile strength of up to 1.5 MPa (10 mm boards), these fire-resistant installation ducts offer long-term reliability. The load-bearing limits of the fasteners – 9 N/mm² tensile strength and 15 N/mm² shear strength up to EI 60, reduced to 6 N/mm² and 10 N/mm² respectively above this rating – ensure stability under fire conditions.
Why should you choose Aestuver® cable ducts?
Whether you need robust fire-resistant enclosures for electrical cables for a small housing development or a large industrial project, Aestuver® offers reliability you can count on.
Manufactured in Calbe, Germany, and certified to ISO 9001:2015 and ISO 14001:2015.
Class A1 building material for a high level of preventive fire protection.
ETA-certified solutions for reliable and traceable fire safety concepts.
Flexible solutions for a range of applications, from individual electrical installations to large-scale industrial projects.
High stability, moisture resistance and abrasion resistance ensure a long service life.
Looking for a fire-resistant enclosure for electrical installations?
We will be happy to support your project.
Get in touch to arrange a technical consultation or request a quote.
More Aestuver® products
Aestuver® fire protection boards are used far beyond tunnels – from structural fire protection in buildings to demanding infrastructure projects and specialist applications.